Fabrication of Capillary Columns with Integrated Frits for Mass Spectrometry

doi:10.1038/protex.2015.049

Method Article

Fabrication of Capillary Columns with Integrated Frits for Mass Spectrometry

https://doi.org/10.1038/protex.2015.049

This work is licensed under a CC BY-NC 3.0 License

This protocol has been posted on Protocol Exchange, an open repository of community-contributed protocols sponsored by Nature Portfolio. These protocols are posted directly on the Protocol Exchange by authors and are made freely available to the scientific community for use and comment.

Version 1

posted

You are reading this latest protocol version

Miniaturization of columns for liquid chromatography has greatly enhanced its sensitivity and resolution. This protocol describes the fabrication of fused silica capillaries with frits and their packing with chromatography media for high-resolution, high-capacity separations suitable for mass spectrometry.

Chemistry

Materials science

Biochemistry

Proteomics

LC-MS

Capillary Column

Column fritting:

Polyimide-coated fused silica capillary from Polymicro by Molex, via Thermo (Polymicro part number), labeled by outer and inner diameters:

360/25 μm (TSP025375)

360/30 μm (TSP030375)

360/50 μm (TSP050375)

360/75 μm (TSP075375)

KASIL 1 (K silicate) from PQ Corporation

Formamide from Sigma (# F9037-100)

MS-grade acetonitrile from Fisher (#A955-212)

MS-grade water from Fisher (#W6-4)

Column packing:

Chromatography material

Acetone from Fisher (#A929-1)

MS-grade acetonitrile from Fisher (#A955-212)

Methanol from Honeywell via VWR (#BJLC230-2.5)

Fused silica diamond cutter tool

Vortex mixer

Optical microscope

Heating block

Nanoscale liquid chromatograph

Scholander chamner, eg pressure bomb

3 mm magnetic stirring bars from Sigma (#Z328839)

Magnetic stirrer

Glass vials

Capillary glass polishing station (ESI Source Solutions)

Column fritting:

Pre-heat the block to 95 °C.
In a clean Axygen tube mix 170 μl K silicate with 30 μl formamide.
Vortex and incubate for 5 minutes at room temperature.
Use cutting tool to cut a piece of silica capillary corresponding to the desired column bed length + 20 cm.
Keeping the capillary almost horizontal, dip the stripped end into the silicate solution until the liquid fills in the capillary (15-30 seconds).
Position the liquid-filled end of the capillary under the heating block and incubate for 8 hours at 95 °C to polymerize silicate.
Mount the capillary on the liquid chromatograph so that the solvent flows from the open end towards the fritted end of the capillary. Flush the capillary with 20 column volumes of 50% acetonitrile and 0.1% formic acid in water.
Visually check for polymerization (frit) at the edge and cut the frit to approximately 1 mm (Figure 1).
The fritted capillary end is polished using the glass polishing station

Column packing:

Preparation: Transfer 5-10 mm3 of bulk material in a clean 2 ml glass vial and resuspend in 1 ml methanol. Wash the material by letting it settle by gravity, removing solvent, and resuspending the material in 1 ml of clean methanol. Wash total 3 times.

In a clean glass vial, dilute 1:10 the bead suspension in carrier (acetonitrile, acetone or methanol). We use acetone for columns with high backpressure given its relatively low viscosity. Add a magnetic stir bar and transfer into the pressure bomb. Make sure that the stirring is sufficient to maintain the particles in suspension.
Mount the fritted capillary. Slide the capillary to reach the bottom of the glass vial and then pull it back up 7-8 mm. Tighten fittings and bomb mount.
Pressurize at 500 psi. Check for flow. Progressively increase the pressure to 1000 psi.
Fill the desired column bed length + 5 cm.
Mount the column on the LC and flow at 80% organic solvent (using the appropriate flow rate) until the pressure trace is stable.

Meiring, H. D.; van der Heeft, E.; ten Hove, G. J.; de Jong, A. P. J. M., Nanoscale LC–MS(n): technical design and applications to peptide and protein analysis. Journal of Separation Science 2002, 25 (9), 557-568.
Ficarro, S. B.; Zhang, Y.; Lu, Y.; Moghimi, A. R.; Askenazi, M.; Hyatt, E.; Smith, E. D.; Boyer, L.; Schlaeger, T. M.; Luckey, C. J.; Marto, J. A., Improved electrospray ionization efficiency compensates for diminished chromatographic resolution and enables proteomics analysis of tyrosine signaling in embryonic stem cells. Analytical chemistry 2009, 81 (9), 3440-7.

No relevant conflicts of interest.

Download PDF

Version 1

posted

You are reading this latest protocol version

Fabrication of Capillary Columns with Integrated Frits for Mass Spectrometry

Status:

Version 1

Abstract

Figures

Reagents

Equipment

Procedure

References

Additional Declarations

Status:

Version 1

Privacy Policy

Terms of Service

Fabrication of Capillary Columns with Integrated Frits for Mass Spectrometry

Status:

Version 1

Abstract

Figures

Reagents

Equipment

Procedure

References

Additional Declarations

Status:

Version 1

Privacy Policy

Terms of Service

Manage Cookie Preferences