Bt-CoV HKU3 PCR/Sequencing Primers

doi:10.1038/protex.2014.025

Method Article

Bt-CoV HKU3 PCR/Sequencing Primers

https://doi.org/10.1038/protex.2014.025

This work is licensed under a CC BY-NC 3.0 License

This protocol has been posted on Protocol Exchange, an open repository of community-contributed protocols sponsored by Nature Portfolio. These protocols are posted directly on the Protocol Exchange by authors and are made freely available to the scientific community for use and comment.

Version 1

posted

You are reading this latest protocol version

This protocol details the primers and conditions used for forward and reverse PCR amplification and sequencing of Bt-CoV HKU3 genomes.

Genetics

Microbiology

Biochemistry

coronavirus

HKU3

genetic analysis

sequencing

This protocol details the steps, reagents, and conditions required to sequence Bt-CoV HKU3 genomes in the forward and reverse directions. The protocol begins with the RT-PCR step, assuming that BtCoV HKU3 RNA purified using a standard procedure (i.e., TRIzol extraction) has already been performed.

Invitrogen SuperScript III kit

dNTPS (10 mM)

Random Hexamers

RNasin (if desired)

Thermo Phusion PCR enzyme

Primers (2 mM stock – see Tables 1 and 2)

Agarose

1X TAE Buffer

Ethidium Bromide

70ºC water bath

55ºC water bath

Thermal cycler

Reverse Transcription:

In a 1.5-µL Eppendorf tube, add 1-4 µL RNA and 1 µL Random Hexamers.
Incubate at 70ºC for 5 min.
Place reaction briefly on ice and assemble the reverse transcription reaction using the kit-supplied reagents (a master mix can be made if multiple reactions are being run): 4 µL 5X First-Strand Buffer

2 µL DTT

1 µL SuperScript III reverse transcriptase

1 µL dNTPs

1 µL RNasin (if desired)

x µL H2O to 20 µL

Incubate at 55ºC for 45 min to 1 h.
Inactivate the reverse transcriptase at 70ºC for 15 min. Place reaction on ice after inactivation.
Proceed with PCR setup.

PCR (with Phusion PCR kit):

Assemble PCR reactions to generate amplicons according to those detailed in Table 3 (for whole-genome sequencing) or with any combination of forward and reverse primers from Tables 1 and 2.
PCR reaction setup: 2 µL First-strand template

1 µL Forward Primer

1 µL Reverse Primer

5 µL 10X HF Buffer

1 µL dNTPs

0.5 µL Phusion polymerase

x µL H2O to 50 µL

PCR reactions are run under standard PCR conditions: 98ºC 5 min

35 cycles of:

98ºC 15 sec

xºC for 30 sec*

72ºC for ~45 sec/kb

72ºC 10 min

8ºC Hold

Annealing temperature is primer-dependent, but for most SARS-CoV primers in Tables 1 and 2, annealing temperatures 52-55ºC will work.

Confirmation of PCR products and sequencing:

Run PCR products (5 µL/reaction) on a 0.8% agarose/1X TAE gel to verify PCR success.
Purify PCR products with PCR purification kit of choice (the Qiagen PCR Purification Kit works well).
PCR products can be diluted to 150-200 µL/reaction to ensure that enough product is present for assembling sequencing reactions.
Assemble sequencing reactions according to the primer/amplicon combinations outlined in Table 3.

Reverse transcription: 1-1.5 h

PCR: 2-4 h

Sequencing: facility-dependent

Primers have been designed to give clean, single-band PCR products. If multiple bands are detected, alternate annealing temperatures may be required. It may also be possible that alternate bands indicate multiple genome patterns at that locus.

None.

supplement0.doc
Table 2 Bt-CoV HKU3 Amplicon Primer Sets
supplement0.doc
Table 1 Bt-CoV HKU3 Sequencing Primers

Download PDF

Version 1

posted

You are reading this latest protocol version

Bt-CoV HKU3 PCR/Sequencing Primers

Status:

Version 1

Abstract

Introduction

Reagents

Equipment

Procedure

Timing

Anticipated Results

Additional Declarations

Supplementary Files

Status:

Version 1

Privacy Policy

Terms of Service

Bt-CoV HKU3 PCR/Sequencing Primers

Status:

Version 1

Abstract

Introduction

Reagents

Equipment

Procedure

Timing

Anticipated Results

Additional Declarations

Supplementary Files

Status:

Version 1

Privacy Policy

Terms of Service

Manage Cookie Preferences